Measures carbon monoxide, oxygen and stack temperature in the flue. At Severance altitude we want CO under 100 ppm, and this tool tells us in minutes whether the burn is clean.
Furnace Maintenance Severance CO that keeps your heat on
Furnace Maintenance Severance CO is the once-a-year work that keeps your system running through a Weld County winter. We clean the burners, test the safety switches, check the heat exchanger and change your filter so you are not calling for emergency heat at 2 a.m.
Serving Severance and nearby areas.
How big is the job?
Tune-up plus parts
Same visit, with a common part like an igniter or capacitor replaced.
- 1. Tune-up Cleaning, testing and a written report on a system that runs.
- 2. Tune-up plus parts Same visit, with a common part like an igniter or capacitor replaced.
- 3. Repair or replace Bigger findings like a cracked exchanger get planned in writing first.
Drag the needle to compareTouch and drag the needle
- 24Services from one local team
- 15Areas served around Severance
- Camera firstHeat exchanger checked before anything else
- Readings keptEvery number written down for next year
What Is Included in Furnace Maintenance in Severance
A standard maintenance visit covers inspection, cleaning, testing and a written report. Parts and repairs are quoted separately, and you approve them before we start.
Work order
Furnace Maintenance- Full Inspection and Camera Check: We inspect the heat exchanger with an inspection camera, check the flue for draft, and look at every electrical connection. This is where we catch cracked exchangers, loose wiring and corrosion before they become expensive problems.
- Burner and Flame Sensor Cleaning: Burners get brushed and vacuumed, and the flame sensor gets cleaned with steel wool.
- Electrical and Airflow Testing: We test the capacitor, blower motor amp draw, limit switch and control board with a multimeter, and read static pressure with a manometer. High static pressure means restricted airflow, which shortens blower motor life.
- Combustion Analysis: A flue gas analyzer measures carbon monoxide, oxygen and stack temperature. At Severance altitude we want CO under 100 ppm in the flue. If it is higher, we adjust gas pressure or flag a part that needs replacing.
- Filter Check and Replacement: We check your filter and swap it if it is loaded up. A clogged filter is the cheapest thing to fix and the most common cause of a furnace that runs hot and short cycles. We can leave you a spare if you want.
- Written Report With Readings: You get a paper report showing every reading we took: static pressure, amp draw, CO levels, temperature rise. Next year we compare against it, so we can spot a part that is drifting before it fails.
What the first visit covers
First visit
We inspect, clean and test the furnace, then hand you the readings in writing.
Furnace Maintenance at Severance homes
Most homes here run high-efficiency furnaces that need annual cleaning and testing.
Newer builds
Sealed combustion and condensate lines checked.
Older furnaces
Pilot, thermocouple and heat exchanger inspected.
Propane systems
Gas pressure adjusted for propane, not natural gas.
Rentals
Written report per address for the property owner.
Furnace Maintenance for Severance businesses
Shops, churches and small commercial buildings need heat that works on a schedule.
Retail shops
Serviced before opening hours.
Churches
Scheduled between services and events.
Small offices
Rooftop and stand-alone units checked.
Furnace Maintenance Severance CO: What It Actually Involves
A furnace that gets looked at once a year runs cleaner, burns less gas and quits less often. Skipping it costs more in the long run. Book the visit before the cold sets in.
Furnace Maintenance Severance CO is a scheduled service visit where a technician inspects, cleans and tests every part of your heating system before it fails. We pull the burners, brush the heat exchanger, check the igniter and flame sensor, test the capacitor and blower motor, and verify the gas valve holds pressure. We use a manometer to read static pressure, a multimeter on the electrical side, and a combustion analyzer to confirm the burn is clean. Most visits take 60 to 90 minutes.
Severance sits at 4,900 feet in Weld County, and that altitude changes how a furnace burns. Thin air means the gas-to-air mix runs lean, so a unit that was fine in another state can soot up a heat exchanger here in two or three seasons. If you search for Furnace Maintenance near me Severance CO in October, you are already behind the rush.
- What it is
- Annual cleaning, testing and inspection of your furnace.
- When it helps
- Before heating season, or when bills and noises change.
- What you get
- A written report with every reading we took.
What to Expect on Furnace Maintenance Day
You get a two-hour window, a call when we are on the way, and a technician who walks you through what he finds.
Tools and Methods We Use on Every Furnace Visit
Each method answers a different question. Together they leave very little to guess.
Reads static pressure and gas pressure. High static pressure means restricted airflow, which we trace to a clogged filter, dirty blower wheel or undersized ductwork.
Tests capacitors, control boards, limit switches and blower motor amp draw. Amp draw above the nameplate rating means the motor is on its way out.
Goes inside the heat exchanger to look for cracks and corrosion you cannot see from the outside. This is how we catch a CO risk before it becomes a hazard.
Reads millivolt output on standing-pilot furnaces. If the reading is low, the thermocouple gets replaced and the pilot holds again.
When Severance Homeowners Call Us for Furnace Service
A homeowner in the Severance Heights area realizes in October that the furnace has not been touched in three years.
We book a fall tune-up, clean the burners and blower, replace the filter, and run a combustion analysis.
HomesA family moves into a newer build off Highway 392 and wants to keep the manufacturer warranty valid.
We set them up on an annual maintenance plan with two visits a year.
HomesA landlord with rentals in Severance and Eaton needs all furnaces serviced before winter to avoid tenant complaints.
We schedule all units on the same day, service each one, and leave a written report per address.
BusinessesA homeowner notices the furnace is banging on startup and the gas bill is creeping up.
We clean the burners, adjust gas pressure, and test the igniter.
Homes
How Furnace Maintenance Runs in Severance, Colorado
Severance sits at about 4,900 feet in Weld County, and that altitude changes how a furnace burns. The air is thinner, so the gas-to-air mix runs lean and burners can soot up faster than at lower elevations.
Severance Heights
Newer construction with high-efficiency furnaces and tight ductwork. Filters load fast here because of ongoing construction dust in the area.
Downtown Severance
Mix of older homes and newer infill. We see more standing-pilot furnaces here, which need thermocouple and pilot orifice checks every year.
County Road 23 Corridor
Rural properties on propane and well water. Propane furnaces need gas pressure adjusted differently than natural gas, and we check that on every visit.
- Severance Heights
- Downtown Severance
- County Road 23 Corridor
- Highway 392 Area
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoThree Years Without Service in Severance
Before: A homeowner near Severance Town Hall had skipped service for three years. Temperature rise was 20 degrees above the manufacturer spec.
After: We cleaned the burners and blower, replaced the flame sensor and filter, and adjusted gas pressure. Temperature rise came back into spec, and the short cycling stopped.
Cracked Heat Exchanger Caught Early
Before: A family in the Highway 392 area called for a routine tune-up on a 12-year-old Carrier. The furnace was running, but the combustion analyzer showed CO at 180 ppm in the flue, well above the safe range.
After: The inspection camera found a cracked heat exchanger. We shut the furnace down, explained the options, and installed a new 96 percent unit the next day. CO readings dropped to under 40 ppm.
Propane Furnace Tune-Up on County Road 23
Before: A rural property on propane had a furnace that banged on startup and ran loud. The burners were dirty, the gas pressure was set for natural gas, and the blower motor was drawing 15 percent above nameplate amps.
After: We cleaned the burners, adjusted the gas pressure and orifice for propane, and replaced the run capacitor. The banging stopped, amp draw came back in spec, and the furnace ran quietly all winter.
Furnace Problems We Catch Before They Cost You
Most no-heat calls in Severance trace back to something a maintenance visit would have found.
Furnace blowing cold air in the middle of winter
Usually a dirty flame sensor or a failed igniter.
Furnace banging or popping when it starts up
Delayed ignition from dirty burners or a weak igniter.
Furnace leaking water on the floor
A clogged condensate line or a cracked drain pan on a high-efficiency unit. Water on the floor can rust the cabinet and damage the furnace base.
Furnace short cycling on and off every few minutes
Often a clogged filter, a failing limit switch or an oversized furnace.
Pilot light will not stay lit on an older furnace
A bad thermocouple or a dirty pilot orifice. Left alone, you lose heat entirely, and in some cases the gas valve can fail next.
Why Severance Homeowners Book Annual Furnace Service
A furnace that gets looked at once a year lasts longer, burns less gas and fails less often.
Lower Gas Bills
A dirty blower wheel and a clogged filter force your furnace to run longer to hit the same temperature.
Fewer Mid-Winter Breakdowns
Nine out of ten no-heat calls we run in January trace back to something an annual visit would have caught: a weak igniter, a…
Longer Equipment Life
A furnace that gets cleaned and adjusted every year routinely runs 15 to 20 years.
Safety You Can Verify
We test the heat exchanger for cracks, check the flue for proper draft, and confirm the limit switch and rollout switches trip when they…
What you get in writing
Clear records you can keep and share.
Inspection findings
What we checked and what we found.
Combustion readings
CO, oxygen and stack temperature numbers.
Filter and airflow notes
Static pressure and temperature rise recorded.
Ten Years Keeping Weld County Furnaces Running
Severance Furnace Repair Pros has been servicing furnaces in and around Severance since 2016.
Flue CO
Read with a flue gas analyzer. Tells us whether the burn is clean or venting badly.
Static pressure
Read with a manometer. High numbers mean restricted airflow somewhere in the system.
Blower amp draw
Read with a multimeter. Above nameplate means the motor is working too hard.
Are you in our Severance service area?
Type your ZIP or town to check. If yours is not listed, call and ask.
Severance ZIP codes
- 80650
- 80546
- 80550
- 80610
What Severance Neighbors Say
Had these guys out for a fall tune-up on my Trane. The tech found a cracked igniter before it failed and had the part on the truck. He showed me the combustion readings on his analyzer and explained what they meant. Furnace ran all winter without a hiccup. Way better than the last company that just vacuumed the filter and left.
We are just outside Severance off County Road 23 and had been putting off service for three years. They cleaned the burners, replaced a flame sensor, and got our temperature rise back in spec. Should have done this sooner.
I manage six rentals in the Severance and Eaton area. Their maintenance plan keeps all six furnaces on a schedule, and I get a written report after every visit. When a tenant calls with no heat, they get priority scheduling. It has cut my emergency repair calls in half.
Furnace Maintenance Questions from Severance Homeowners
Short answers for the first few minutes. The team can cover the rest.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
(970) 1234567That covers the full inspection, burner cleaning, combustion test and written report. Repairs found during the visit are priced separately, and you approve them before we start.
Once a year, ideally in early fall before the heating season starts. Severance sits at high altitude with dusty air and hard freeze cycles, so furnaces here collect debris faster than at lower elevations. If you have pets, a large family or a system over 12 years old, we sometimes recommend a mid-season check as well.
We do. Severance Furnace Repair Pros offers a plan with two visits per year, priority scheduling during cold snaps, and a discount on any repairs. You get a reminder when your next visit is due, so you are not the person calling on the coldest night of the year. Call (970) 1234567 to sign up or ask what the plan covers.
Every visit includes a filter check, burner cleaning, flame sensor and igniter inspection, heat exchanger inspection with a camera, blower motor amp draw test, capacitor test, gas pressure check, and a combustion analysis with a flue gas analyzer. You get a written report with the readings. Parts and repairs are extra, and we quote them before doing the work.
Other Furnace Services We Handle in Severance
Other services from the same team.
Book Furnace Maintenance Severance CO Before Winter Hits
(970) 1234567Fall slots fill fast in Severance, and the first hard freeze usually lands in late October. Call (970) 1234567 and we will get your furnace cleaned, tested and ready.
Call for Furnace Repair in Severance
Call (970) 1234567 and describe what your furnace is doing. We answer, triage the symptom and give you a two-hour arrival window. Regular hours run 8 a.m. to 6 p.m. Monday through Friday, with emergency coverage for no-heat calls. If you are in ZIP 80650, 80546, 80550 or 80610, you are in our regular service area.