Measures gas pressure at the valve and burners to confirm the furnace is operating within manufacturer spec.
Commercial Furnace Repair in Severance That Keeps Your Business Running
When your building's heat goes down, Commercial Furnace Repair in Severance from our team gets you back up and running fast. We service gas, electric, and propane commercial furnaces across Severance, CO and Weld County.
Serving Severance and nearby areas.
How big is the job?
Motor or board
Blower motor, control board, or gas valve replacement with full testing.
- 1. Component swap Igniter, thermocouple, or flame sensor replacement on a single furnace.
- 2. Motor or board Blower motor, control board, or gas valve replacement with full testing.
- 3. Heat exchanger Heat exchanger replacement or multi-furnace repair, planned in writing first.
Drag the needle to compareTouch and drag the needle
- 24Services from one local team
- 15Areas served around Severance
- Camera firstWe inspect the heat exchanger before quoting.
- Readings keptYou get the test numbers in writing.
What Our Commercial Furnace Repair Includes
Every commercial furnace repair call includes a full diagnostic, a written quote, the repair itself, and post-repair testing.
Work order
Commercial Furnace Repair- Full Diagnostic Assessment: We test the igniter, flame sensor, control board, blower motor, capacitor, and limit switch. Gas pressure is checked with a manometer, and combustion is analyzed with a flue gas analyzer. We use an inspection camera to check the heat exchanger for cracks.
- Flat-Rate Repair Quote: Before we start any repair, you get a written flat-rate quote. The quote covers parts and labor with no hourly surprises. If the repair isn't worth it, we'll tell you and quote a replacement instead.
- Component Repair or Replacement: We replace failed igniters, thermocouples, flame sensors, control boards, blower motors, gas valves, capacitors, and limit switches. Our trucks carry common parts for Carrier, Trane, Goodman, Rheem, Lennox, Bryant, York, and American Standard furnaces.
- Post-Repair Testing: After the repair, we run a full heating cycle and verify temperature rise. We check for gas leaks, confirm combustion readings are within spec, and test all safety controls. You get the readings in writing.
- Written Documentation: You receive a written summary of what failed, what we replaced, and our test readings. We include photos of the failed part and the completed repair. This documentation supports insurance claims and inspection requirements.
What the first visit covers
First visit
We diagnose the furnace, test all safety controls, and give you a written quote before any repair.
Commercial Furnace Repair at homes
Home-based businesses and residential buildings with commercial-grade furnaces.
Home office heat
Furnace serving a dedicated workspace.
Rental property
Tenant-occupied building with a commercial furnace.
Mixed-use home
Residential space with a light-commercial system.
Home workshop
Detached shop or garage with a commercial furnace.
Commercial Furnace Repair at businesses
Retail, office, restaurant, and warehouse buildings across Severance and Weld County.
Retail strip mall
Multi-tenant buildings with shared or individual furnaces.
Restaurant
Dining and kitchen areas needing reliable heat.
Warehouse
Large-volume spaces with rooftop or split-system furnaces.
Commercial Furnace Repair in Severance: What It Covers
Commercial furnace repair is worth doing properly because a failed heat exchanger or control board can shut your building down and create safety hazards. We diagnose the whole system, not just the obvious part.
Commercial Furnace Repair in Severance is the diagnosis and repair of heating systems in commercial buildings, from rooftop units to split-system furnaces. Our technicians test the igniter, flame sensor, control board, blower motor, and heat exchanger with a multimeter and combustion analyzer. We check gas pressure with a manometer, inspect the flue, and verify the limit switch and capacitor are within spec. Every repair follows ACCA standards and local mechanical code, so your building stays warm and your inspection passes.
Severance sits in Weld County where winter nights drop below 10 degrees, and commercial buildings here take a beating. Older strip-mall furnaces short-cycle, restaurants deal with grease-clogged filters, and warehouses see failed blower motors after years of heavy use. If you need business furnace repair Severance property managers trust, we stock common parts for Carrier, Trane, Goodman, Rheem, Lennox, Bryant, York, and American Standard units. That means fewer return trips and faster heat restoration for your tenants.
- What it is
- Diagnosis and repair of commercial building heating systems.
- When it helps
- When your building loses heat or the furnace acts up.
- What you get
- A written diagnosis, a flat-rate quote, and a documented repair.
Our Commercial Furnace Repair Process
From your first call to final testing, here's exactly what happens when you hire us for commercial furnace repair in Severance.
Tools and Methods We Use for Commercial Furnace Repair
Each method answers a different question. Together they leave very little to guess.
Tests electrical components including igniters, flame sensors, control boards, and blower motors for continuity and voltage.
Reads flue gas oxygen, carbon monoxide, and temperature to verify safe, efficient combustion after repairs.
Checks thermocouple output on standing-pilot furnaces to confirm the pilot will stay lit.
Measures flue gas composition to detect incomplete combustion, cracked heat exchangers, and venting problems.
When Severance Businesses Call Us for Furnace Repair
A retail strip mall in Severance loses heat on a Saturday morning and tenants are calling the property manager.
We dispatch a technician within two hours, diagnose a failed blower motor, and replace it with a part from our truck.
BusinessesA Severance restaurant's dining room furnace short-cycles during dinner service, making the space uncomfortable for customers.
We schedule a next-morning visit, clean the flame sensor, adjust gas pressure with a manometer, and verify combustion with a flue gas…
BusinessesA warehouse in Weld County has a cracked heat exchanger and needs repair before an insurance inspection.
We document the crack with camera photos, quote the heat exchanger replacement, and schedule the work around the warehouse's shipping hours.
BusinessesAn office building in Severance has a furnace that won't turn on, and the building manager needs it fixed before Monday.
We come out on Sunday, diagnose a failed control board, and replace it with a compatible unit from our truck.
Businesses
How Commercial Furnace Repair Works in Severance
Severance sits at 4,800 feet in Weld County, where winter design temperatures hit 5 degrees and heating season runs from October through April. Commercial buildings here face dry air, temperature swings, and furnaces that run hard for six months straight.
Downtown Severance
Older commercial buildings with original furnaces that need frequent igniter and thermocouple replacements.
Severance Business Park
Newer light-industrial buildings with rooftop units and split-system commercial furnaces.
Weld County Road 74 corridor
Mixed-use properties where furnaces serve both office and warehouse space.
- Downtown Severance
- Severance Business Park
- Weld County Road 74 corridor
- Severance High School area
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoStrip Mall Blower Motor Replacement
Before: A Severance strip mall lost heat on a Friday afternoon. The furnace was blowing cold air, and tenants were calling the property manager. The blower motor had seized after 10 years of service.
After: We replaced the blower motor with a part from our truck and had heat restored within three hours. Temperature rise was verified at 45 degrees, and the building stayed open through the weekend.
Restaurant Flame Sensor Cleaning
Before: A Windsor restaurant's dining room furnace was short-cycling every 10 minutes during dinner service. The flame sensor was coated with carbon, causing the furnace to shut down mid-cycle.
After: We cleaned the flame sensor, adjusted gas pressure to spec, and replaced the dirty filter. The furnace ran continuously through a 30-minute test cycle with stable combustion readings.
Warehouse Heat Exchanger Replacement
Before: A Greeley warehouse furnace had a cracked heat exchanger documented by our inspection camera. The furnace was still running, but carbon monoxide levels were elevated and the building failed an insurance inspection.
After: We replaced the heat exchanger, tested all safety controls, and verified combustion with a flue gas analyzer. The warehouse passed re-inspection, and carbon monoxide readings returned to safe levels.
Commercial Furnace Problems We Solve in Severance
Commercial furnaces fail in predictable ways. Here are the most common problems we see in Severance buildings and how we fix them.
Furnace blowing cold air during business hours
Tenants complain, customers leave, and your building loses heat fast.
Furnace won't turn on at all
No heat means no business. A furnace that won't turn on could be a tripped limit switch, failed thermocouple, or dead control board.
Furnace banging or booming noise
Banging noises often mean delayed ignition, which stresses the heat exchanger and can crack it.
Furnace leaking water around the base
Water around a commercial furnace can damage flooring, create slip hazards, and indicate a blocked condensate drain or failed inducer motor.
Why Severance Businesses Call Us First
Commercial heating failures cost you tenants, customers, and productivity. Here's what you get when you call our team for commercial furnace repair in Severance.
Same-Day Heat Restoration
We prioritize commercial no-heat calls and aim for same-day Commercial Furnace Repair Severance CO businesses depend on.
Code-Correct Repairs
Every repair meets local mechanical code and ACCA standards.
Minimal Business Disruption
We schedule around your operating hours and work quietly in mechanical rooms. For retail and restaurant clients, we can stage repairs during slow periods.
Affordable Business Furnace Repair Severance Rates
We quote the repair before we start, so there are no surprise invoices.
What you receive
Clear records you can keep and share.
Written diagnosis
A summary of what failed and why.
Test readings
Combustion, gas pressure, and temperature numbers.
Repair photos
Images of the failed part and completed work.
10 Years of Commercial Heating Expertise
Severance Furnace Repair Pros has been fixing commercial furnaces since 2016.
Combustion readings
We read flue gas oxygen and carbon monoxide to confirm safe, efficient operation after any repair.
Gas pressure
We measure pressure at the valve and burners to verify the furnace is running within manufacturer spec.
Temperature rise
We compare return and supply air temperatures to confirm the furnace is heating within its rated range.
Are you in our Severance service area?
Type your ZIP or town to check. If yours is not listed, call and ask.
Severance ZIP codes
- 80650
- 80546
- 80550
- 80610
What Severance Businesses Say About Our Work
Our strip mall lost heat on a Friday afternoon in January. Severance Furnace Repair Pros had a tech out within two hours and diagnosed a failed blower motor. They had the part on the truck and we had heat back before close. The written report with test readings was exactly what our insurance wanted.
Our dining room furnace started short-cycling during dinner service. These guys came out the next morning, cleaned the flame sensor, adjusted the gas pressure, and showed me the combustion readings. No more short cycling, and our gas bill dropped noticeably. Fair price and no upsell.
We had a cracked heat exchanger in our warehouse furnace. Severance Furnace Repair Pros documented it with camera photos, quoted the replacement, and had us back up in two days. They worked around our shipping schedule and left the mechanical room cleaner than they found it.
Frequently Asked Questions About Commercial Furnace Repair in Severance
Short answers for the first few minutes. The team can cover the rest.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
(970) 1234567Igniter and flame sensor replacements sit at the low end; blower motors and control boards cost more. We quote the repair before starting, so you know the number upfront. Call (970) 1234567 for a same-day diagnosis.
Severance Furnace Repair Pros handles business furnace repair in Severance, Colorado. We've served Weld County commercial properties since 2016 and work on all major brands including Carrier, Trane, Goodman, Rheem, Lennox, Bryant, York, and American Standard. Call (970) 1234567 to schedule.
Call us as soon as you notice symptoms like cold air, banging noises, or short cycling. We prioritize commercial no-heat calls and aim for same-day service. Our trucks carry common parts, so most repairs finish in one visit. For planned work, we schedule around your operating hours to avoid disrupting tenants or customers.
Yes. We offer commercial furnace maintenance in Severance CO with annual or semi-annual service plans. Maintenance includes filter changes, flame sensor cleaning, combustion analysis, and heat exchanger inspection. Regular tune-ups catch failing components before they cause downtime. Call (970) 1234567 to set up a maintenance schedule for your building.
Related Heating Services in Severance
Other services from the same team.
- Propane Furnace RepairPropane furnaces run hotter and sootier than natural gas, so we check the heat exchanger and burner orifices…
- Furnace MaintenanceAnnual maintenance that catches dirty flame sensors, worn capacitors and clogged filters before they strand you in a…
- Furnace Tune-UpA tune-up is the cheap insurance on a furnace.
Need Commercial Furnace Repair in Severance Today?
(970) 1234567Don't let a failed furnace cost you tenants or customers. Call Severance Furnace Repair Pros at (970) 1234567 for same-day Commercial Furnace Repair in Severance. We diagnose fast, quote upfront, and fix it right.
Call for Furnace Repair in Severance
Call (970) 1234567 and describe what your furnace is doing. We answer, triage the symptom and give you a two-hour arrival window. Regular hours run 8 a.m. to 6 p.m. Monday through Friday, with emergency coverage for no-heat calls. If you are in ZIP 80650, 80546, 80550 or 80610, you are in our regular service area.